Polishing of wall and ceiling surfaces

A badly installed surface and a surface with holes or damages caused by rusting of reinforcement that has not been placed deep enough provide mainly unaesthetical appearance to unplastered concrete surfaces. Such surfaces are also relatively difficult to clean and maintain. Solution to this problem is polishing with a suitable levelling compound.

If defects and damages are small and scarce, repairing is performed locally, otherwise additionally smooth the entire concrete surface. In both cases, apply levelling compound JUBOLIN (manual application) or JUBOLIN P-25 (machine or manual application).

Remove all loose and badly adhered particles, remains of panelling oils and other dirt from concrete surface (the best way to do it is to wash it), clean rust from the “uncovered” reinforcement and protect it with suitable coatings against further rusting. Then, coat the concrete surface with diluted ACRYL EMULSION (ACRYL EMULSION : water = 1 : 1). Levelling compound is applied onto a dry primer (manual application: JUBOLIN or JUBOLIN P-25; machine application: JUBOLIN P-25), usually in two, but if necessary, in more coats in thickness of 1 to 2 mm. Sand the completely dry final coat (if necessary, lower ones as well) manually or by a machine.

to polish a m² of medium rough surface, you will need  ~1.5 to 2 kilos of levelling compound JUBOLIN (manual application) or the levelling compound JUBOLIN P-25 (machine or manual application) and  ~0.1 kilo of AKRIL EMULSION for the preparation of the substrate

Videz prebarvanih fino ometanih površin ali mavčnokartonskih oblog bistveno izboljšamo, če jih pred barvanjem ustrezno zgladimo. Za glajenje uporabimo JUBOLIN
ali NIVELIN (ročni nanos) oziroma JUBOLIN P-25 (strojni ali ročni nanos). 

Očiščeno podlago premažemo z razredčeno AKRIL EMULZIJO (AKRIL EMULZIJA : voda = 1 : 1), le problematične mavčnokartonske plošče slabše kvalitete z razredčenim JUKOLOM (JUKOL : voda = 1 : 1). Izravnalno maso ročno - z nerjavečo jekleno gladilko (JUBOLIN ali JUBOLIN P-25 ali NIVELIN) - ali strojno - z brizganjem (JUBOLIN P-25) - nanesemo na suh prednamaz, običajno v dveh, če je potrebno pa tudi v več, 1 do 2 mm debelih slojih. Ne glede na način nanašanja, odvečno maso z obdelovane ploskve odvzemamo z nerjavečo jekleno gladilko, pri čemer skušamo površino čim bolj zgladiti. Prvi sloj pred nanosom drugega, enako pa tudi drugi oziroma zaključni sloj , obrusimo s finim brusnim papirjem. Brušenje je lahko ročno ali strojno. 

za glajenje m² velike srednje hrapave površine zadošča ~1,5 do 2 kg JUBOLINA (ročni nanos) ali JUBOLINA P-25 (ročni ali strojni nanos) ali ~1 do 1,5 kg NIVELINA (ročni nanos) in ~0,1 kg AKRIL EMULZIJE, oziroma ~0,1 kg JUKOLA pri manj kvalitetnih mavčnokartonskih ploščah

The appearance of painted fine plastered surfaces or gypsum-cardboard linings can be substantially improved if these substrates are levelled prior to painting.
Use JUBOLIN or NIVELIN (manual application) or JUBOLIN P-25 (machine or manual application) for polishing.                                                                                                    

Cover the clean substrate with diluted ACRYL EMULSION (ACRYL EMULSION : water = 1 : 1), and only problematic gypsum-cardboard boards of poorer quality with diluted JUKOL (JUKOL : water = 1 : 1). Apply levelling compound manually using a stainless steel smoothing trowel (JUBOLIN or JUBOLIN P-25 or NIVELIN) or using a machine (by spraying; JUBOLIN P-25) onto a dry primer, usually in two, but if necessary, in more coats in thickness of 1 to 2 mm. Regardless of the manner of application, remove excess compound from the treated surface using a stainless steel smoothing trowel, while trying to smooth the surface as much as possible. Sand the first coat with sandpaper prior to the application of the second one, and the same with the second or the final coat. Grinding can be either manual or performed by a machine.

to polish a m² of medium rough surface, you will need ~1.5 to 2 kilos of JUBOLIN (manual application) or JUBOLIN P-25 (manual or machine application) or ~1 to 1.5 kilo of NIVELIN (manual application) and ~0.1 kilo of AKRIL EMULSION or ~0.1 kilo of JUKOL.

Remove old paint applications entirely by grinding or scraping and then remove all dust from the substrate (if possible, wash it with a wet cloth or sponge). Use JUBOLIN or NIVELIN (manual application) or JUBOLIN P-25 (machine or manual application)for polishing.                                                                                               

Cover the clean substrate with diluted ACRYL EMULSION (ACRYL EMULSION : water = 1 : 1). Apply levelling compound manually using a stainless steel smoothing trowel (JUBOLIN or JUBOLIN P-25 or NIVELIN) or using a machine (by spraying; JUBOLIN P-25) onto a dry primer, usually in two, but if necessary, in more coats in thickness of 1 to 2 mm. Regardless of the manner of application, remove excess compound from the treated surface using a stainless steel smoothing trowel, while trying to smooth the surface as much as possible. Sand the first coat with sandpaper prior to the application of the second one, and the same with the second or the final coat. Grinding can be either manual or performed by a machine.

to polish a m² of medium rough surface, you will need ~1.5 to 2 kilos of  JUBOLIN
(manual application) or JUBOLIN P-25 (manual or machine application)or ~1 to 1.5 kilo of  NIVELIN (manual application) and ~0.1 kilo of  AKRIL EMULSION.

Remove old paint applications entirely by grinding or scraping and then remove all dust from the substrate (if possible, wash it with a wet cloth or sponge). Use JUBOLIN or NIVELIN (manual application) or JUBOLIN P-25 (machine or manual application) for polishing.                                                                                                    

Cover the clean substrate with diluted ACRYL EMULSION (ACRYL EMULSION : water = 1 : 1). Apply levelling compound manually using a stainless steel smoothing trowel (JUBOLIN or JUBOLIN P-25 or NIVELIN) or using a machine (by spraying; JUBOLIN P-25) onto a dry primer, usually in two, but if necessary, in more coats in thickness of 1 to 2 mm. Regardless of the manner of application, remove excess compound from the treated surface using a stainless steel smoothing trowel, while trying to smooth the surface as much as possible. Sand the first coat with sandpaper prior to the application of the second one, and the same with the second or the final coat. Grinding can be either manual or performed by a machine.

to polish a m² of medium rough surface, you will need ~1.5 to 2 kilos of  JUBOLIN
(manual application) or JUBOLIN P-25 (manual or machine application)or ~1 to 1.5 kilo of NIVELIN (manual application) and ~0.1 kilo of  AKRIL EMULSION

Remove old paint applications entirely by grinding or scraping and then remove all dust from the substrate (if possible, wash it with a wet cloth or sponge). Use JUBOLIN or NIVELIN (manual application) or JUBOLIN P-25 (machine or manual application) for polishing.                                                                                                    

Cover the clean substrate with diluted ACRYL EMULSION (ACRYL EMULSION : water = 1 : 1). Apply levelling compound manually using a stainless steel smoothing trowel (JUBOLIN or JUBOLIN P-25 or NIVELIN) or using a machine (by spraying; JUBOLIN P-25) onto a dry primer, usually in two, but if necessary, in more coats in thickness of 1 to 2 mm. Regardless of the manner of application, remove excess compound from the treated surface using a stainless steel smoothing trowel, while trying to smooth the surface as much as possible. Sand the first coat with sandpaper prior to the application of the second one, and the same with the second or the final coat. Grinding can be either manual or performed by a machine.
to polish a m² of medium rough surface, you will need ~1.5 to 2 kilos of JUBOLIN
(manual application) or JUBOLIN P-25 (manual or machine application)or ~1 to 1.5 kilo of NIVELIN(manual application) and ~0.1 kilo of AKRIL EMULSION.

If old paint applications are well adhered to the substrate, they do not have to be removed. Remove all dust from the substrate (if possible, wash it with a wet cloth or sponge). Use JUBOLIN or NIVELIN (manual application) or JUBOLIN P-25 (machine or manual application) for polishing.                                                                                                    

Cover the clean substrate with diluted ACRYL EMULSION (ACRYL EMULSION : water = 1 : 1). Apply levelling compound manually using a stainless steel smoothing trowel (JUBOLIN or JUBOLIN P-25 or NIVELIN) or using a machine (by spraying; JUBOLIN P-25) onto a dry primer, usually in two, but if necessary, in more coats in thickness of 1 to 2 mm. Regardless of the manner of application, remove excess compound from the treated surface using a stainless steel smoothing trowel, while trying to smooth the surface as much as possible. Sand the first coat with sandpaper prior to the application of the second one, and the same with the second or the final coat. Grinding can be either manual or performed by a machine.
to polish a m² of medium rough surface, you will need ~1.5 to 2 kilos of JUBOLIN
(manual application) or JUBOLIN P-25 (manual or machine application)or ~1 to 1.5 kilo of NIVELIN(manual application) and ~0.1 kilo of AKRIL EMULSION.